 |
| |
 |
Socket |
|
CPU |
|
CPU Compatibility |
|
| Intel |
1155/1156 |
Core i7 |
Supports all speeds |
| Core i5 |
| Core i3 |
| 1366 |
Core i7 |
Supports all speeds |
| 775 |
Core 2 Extreme |
Supports all speeds |
| Core 2 Quad |
| Core 2 Duo |
| Pentium D |
| Pentium 4 |
| Celeron D |
| AMD |
FM1 |
LIano |
Supports all speeds |
| FM2 |
Trinity |
Supports all speeds |
| AM3+ |
Vishera |
Supports all speeds |
| Zambezi |
| AM3 |
Phenom II |
Supports all speeds |
| Athlon II |
| AM2+ |
Phenom II |
Supports all speeds |
| Phenom |
| Athlon FX |
| Athlon X2 |
| Athlon |
| Sempron |
| AM2 |
Athlon FX |
Supports all speeds |
| Athlon X2 |
| Athlon |
| Sempron |
| 940 |
Dual-Core Opteron |
Supports all speeds |
| Opteron |
| Athlon FX |
| 939 |
Dual-Core Opteron |
Supports all speeds |
| Opteron |
| Athlon FX |
| Athlon X2 |
| Athlon |
| 754 |
Athlon |
Supports all speeds |
| Sempron |
|
| |
 |
 |
|
| Cases equipped with an Air Guide must have their Air Guide
Ducts removed before installation. Install only on systems meeting
the following conditions. |
| |
 |
There must be no interfering components (e.g.
PSU, VGA card) within 56mm distance from the center
of the PSU. |
|
 |
There must be no interfering components (e.g.
ODD) within 45mm distance from the center of the
CPU. |
|
 |
Case chassis cover must be distanced at least
135mm away from the motherboard. |
|
|
|
|
| |
 |
|
 |
|
| Dimensions |
85(L) x 112(W) x 125(H) mm |
| Weight |
530g |
| Base Material |
Pure Copper |
| Dissipation Area |
3,698㎠ |
| Thermal Resistance |
0.12 ~ 0.16°C/W |
|
| |
 |
|
| Bearing Type |
2 Ball-Bearing |
| Speed |
1,350rpm ± 10 % ~ 2,600rpm ± 10 % |
| Noise Level |
18.0dBA ± 10% ~27.5dBA ± 10% |
|
|
 |
| Dimensions : 70(L) x 26(W) x 26(H) mm |
Weight : 20g |
Output Voltage : 5V ~ 11V ± 2% |
|
| Allowable Power : 6W or lower |
Connector : 3-Pin |
 |
|
|
| |
 |
|
Does not generate noise or vibration in Silent Mode.
|
|
|
Pure copper heatsink with component layout optimized
for maximum cooling efficiency. |
|
|
Innovative, patented, and curved heatpipe design for
a heat transfer capacity of up to six heatpipes with the
use of just three. |
|
 |
Ultra slim fins (0.2mm) for minimized weight and reduced
airflow resistance. |
|
 |
Equipped with Zalman`s low noise 92mm fan. |
|
 |
Supports all single and dual core CPUs of Intel`s Socket
1155/1156/775 and all single and dual core CPUs of AMD`s
Socket FM2/FM1/AM3+/AM3/AM2+/AM2/754/939/940. |
|
 |
The adjustable fan speed controller (FAN MATE 2) enables
control of noise and cooling performance. |
|
|
|
| |
 |
 |
| Common Components |
|
- Cooler (CNPS9500A LED)
- FAN MATE 2
- FAN MATE 2 Cable
- Double-Sided Tape
- Thermal Grease (ZM-STG2M)
- User`s Manual |
| |
| Intel Components |
|
- Clip Support
- Clip Support Fixing Bolts
- Intel Clip
- Washers
- Nuts
- Clip Fixing Bolts |
| |
| AMD Components |
|
- AMD Clip
- AMD Clip Lever |
|
|
|
| |
 |
| Zalman affixes a Computer Noise Prevention System (CNPS) mark to all components
used for noiseless computers. |
| |
 |
|
Korean Patent Application No.10-0600448 |
|
|
Korean Design Application No. 30-0403411, 0403412 |
|
|
Patent applications pending in over 20 nations around the world
including USA, EU, and Japan. |
|
| |
 |
|
The maximum weight specified for a cooler is 450g for Intel Socket
1155/1156/775 and AMD Socket FM2/FM1/AM3+/AM3/AM2+/AM2/754/939/940.
Special care and attention must be taken when moving a computer equipped
with a cooler exceeding the specified weight limit. Zalman Tech Co.,
Ltd. is not responsible for any damage resulting from moving a computer.
|
|
|
Excessive force exerted on the fan may damage the fan, resulting
in damage to the system. |
|
|
Do not ingest or make oral contact with the Thermal Grease. If ingested,
get medical attention.
Disclaimer) Zalman Tech Co., Ltd. is not responsible for any damages
due to external causes, including but not limited to, improper use,
problems with electrical power, accident, neglect, alteration, repair,
improper installation, or improper testing. |
|
|
The computer system may automatically shut down when booting the
computer after the system monitoring program outputs a warning stating
that the CPU fan is rotating slowly. In such a case, fully turn the
Speed Control Knob in the clockwise direction before rebooting to
disable the `CPU Fan Detected` option in BIOS, or set the CPU fan`s
rotational speed to 1,350rpm or lower in the system monitoring program.
|
|
|
Zalman Tech Co., Ltd. is not responsible for any damages resulting
from CPU Overclocking. |
|
