Silent CPU cooler built with pure copper for enhanced performance and optimized compatibility design.
Socket CPU CPU Compatibility
Intel 1155/1156 Core i7 Supports all speeds
Core i5
Core i3
1150 Core i7 Supports all speeds
Core i5
775 Core 2 Quad Supports all speeds
Core 2 Duo
Pentium Dual Core
Pentium D
Pentium 4 Prescott Up to 540
Cedar Mill Up to 650
Celeron D Supports all speeds
AMD FM2 Trinity 95W or lower
FM1 Llano 95W or lower
AM3+ Vishera 95W or lower
Zambezi 95W or lower
AM3 Phenom II Up to 945 (lower than 95W)
Athlon II Supports all speeds
AM2+ Phenom Up to 9650 (lower than 95W)
Athlon FX Supports all speeds
Athlon X2
AM2 Athlon FX Supports all speeds
Athlon X2
940 Opteron Supports all speeds
Athlon FX
939 Opteron Supports all speeds
Athlon FX
Athlon X2
754 Athlon Supports all speeds
No motherboard components with a height greater than 39mm, as well as the PSU, disk drives, VGA card, and RAM should be present within a 55mm radius from the center of the CPU.
Dimensions 109(L) x 107(W) x 63(H) mm
Weight(1) 750g
Base Material Pure Copper
Dissipation Area 2,890㎠
Bearing Type 2 Ball-Bearing
Speed(2) 1,350rpm ± 10% ~ 2,400rpm ± 10%
Noise Level(3) 17.0dBA ± 10% ~ 24.0dBA ± 10%
(1) The maximum weight for a cooler is specified as 450g for Intel Socket 775 and AMD Socket AM2/754/939/940. Special care
should be taken when moving a computer equipped with a cooler which exceeds the relevant weight limit. Zalman is not
responsible for any damage that occur while moving a computer.
(2) The fan operates at 2,650rpm(27.5dBA±10%) if directly connected to the motherboard’s power connector without the use of
(3) Measured 1m distance away from source.
Dimensions : 70(L) x 26(W) x 26(H) mm Weight : 20g Output Voltage : 5V ~ 11V ± 2%
Allowable Power : 6W or lower Connector : 3-Pin
Does not generate noise or vibration in Silent Mode.
Pure copper base materials ensure excellent heat dissipation.
Compatible with single and dual core CPUs for Intel Socket 1150/1155/1156/775 and AMD Sockets FM2/FM1/AM3+/AM3/AM2+/AM2/754/939/940.
92mm fan inside the heatsink maximizes airflow.
Adjustable fan speed controller(FAN MATE 2) enables control of noise and fan performance.
Common Components
- Cooler (CNPS7000C-Cu)
- Clip Support
- Clip Support Fixing Bolts
- Washers
- Nuts
- Thermal Grease(ZM-STG2M)
- FAN MATE 2 Cable
- Double-Sided Tape
- User’s Manual
Intel Components
- Intel Clip
- Intel Clip Fixing Bolts
AMD Components
- AMD Clip
- AMD Clip Lever
Zalman affixes a Computer Noise Prevention System (CNPS) mark to all components used for noiseless computers.
The computer system may automatically shut down when booting the computer after the system monitoring program outputs a warning stating that the CPU fan is rotating slowly. In such a case, fully turn the Speed Control Knob in the clockwise direction before rebooting to disable the 'CPU Fan Detected' option in BIOS, or set the CPU fan's rotational speed to 1,350rpm or lower in the system monitoring program.
Note) Some motherboards fail to boot if the rotational speed of the CPU fan is below a certain rpm. However, booting can be possible even at low fan rpm if the BIOS settings are updated. For more information on updating the BIOS, please refer to the
website of the motherboard's manufacturer. There are motherboards which fail to detect the rpm while operating the cooler in Silent Mode, but this does not affect computing performance.
Excessive force exerted on the fan may damage the fan, resulting in damage to the system.
Zalman Tech Co., Ltd. is not responsible for any damages resulting from CPU Overclocking.
Liquid metal thermal grease unlike the normal thermal grease it contains electrical conductivity and causes aluminum cooler to rust therefore please avoid using it. Corrosion and short circuits caused by using aluminum cooler are users' responsibility, so please read this carefully before using. (EX: Liquid Pro, Liquid Ultra etcs)